How do you make an IV solution with insulin?
How do you make an IV solution with insulin?
Intravenous insulin administration is as follows:
- Mix 250 units of regular human insulin in 250 mL of normal saline (1 U/mL).
- Flush approximately 30 mL through the line prior to administration.
- Do not use a filter or filtered set with insulin.
Which of the following types of syringes should be used in the mixing of vinblastine quizlet?
Which of the following types of syringes should be used in the mixing of Vinblastine? Luer lock. The two parts of the syringe that should not be touched and remain sterile are: The tip and plunger.
Which procedure would you not do when opening an ampule after wiping with an alcohol pad dry the neck with a paper towel?
Aseptic Technique
| A | B |
|---|---|
| What should you not do when opening an ampule | After wiping with an alcohol pad, dry the neck with a paper towel |
| As a technician, you are asked to prepare an IV solution with insulin | You should use only regular insulin. The other insulin cannot be given by IV. |
What protective apparel must be worn when reconstituting vinblastine?
What protective apparel must be worn when reconstituting Vinblastine? 2 pair of gloves (double gloving), a hair covering, a mask and a protective barrier gown.
What part of the syringe should not be touched?
Do not touch: the shaft of the needle; • the bevel of the needle; • the adaptor of the needle; • the adaptor of the syringe; • the plunger seal of the syringe; • the plunger shaft of the syringe. If you touch any of these parts by accident, discard the syringe and needle and get new sterile ones.
Which solution is recommended for cleaning a laminar flow hood?
Use 70% ethanol as the disinfectant unless otherwise specified by the hood manufacturer. Soap and water should not be used.
What two parts of a syringe should not be touched?
How much Ampicillin is in 1 mL of sterile water?
It doesn’t mean there is 250 mg of ampicillin in the vial, it means that once mixed with sterile water, each ml will have 250mg of ampicillin in it. Once again, the amount of sterile water is unimportant for you in determining how many mls to administer in order to give the ordered dose (2.6 mls doesn’t matter!).
How to calculate the amount of reconstituted solution to inject?
To figure the correct amount of reconstituted solution to inject I will use “ratios and proportions” so the formula I will use is: To work this formula you first multiply 2 ml x 0.5 IU, this equals 1.0 ml. Then you divide the 1.0 ml by 5 IU, which will give you 0.2 ml (0.2 cc), which is the answer.
How are sterile solutions used in the reconstitution process?
Sterile solutions are always used to reconstitute medications for injectable use. Special diluents, when required for reconstitution, are usually packaged with the powdered medication; but oral medications can often be, but are not always, reconstituted with tap water. Thus the nurse must know how the reconstitution process works.
What kind of solution to use when reconstituting medicine?
When reconstituting medications, read the directions to find out which diluent needs to be used. Water or normal saline (NS) solution is often used to dilute medicines and to liquefy dry, powdered forms of medicines. Dilution Extent to which the concentration of a mixture is reduced.
What is the dosage of sterile water for irrigation?
Dosage Forms And Strengths. Irrigation. 250, 500, 1000, and 1500 mL sterile water for irrigation in a single-dose plastic pour bottle. 1000, 2000 and 3000 mL sterile water for irrigation in a single-dose flexible plastic container.
To figure the correct amount of reconstituted solution to inject I will use “ratios and proportions” so the formula I will use is: To work this formula you first multiply 2 ml x 0.5 IU, this equals 1.0 ml. Then you divide the 1.0 ml by 5 IU, which will give you 0.2 ml (0.2 cc), which is the answer.
Can you use sterile water for intravenous injection?
Not for intravenous injection. Sterile Water for Irrigation is hypotonic with an osmolarity of zero mOsmol/L. It is intended for use as an irrigation fluid and not for intravenous administration or administration by other, parenteral routes (e.g., subcutaneous or intramuscular) [see WARNINGS AND PRECAUTIONS].
What kind of diluent do you use to reconstitute a medication?
correctly so that you use the proper diluent and volume needed to reconstitute the medication. If the correct diluent is not used, the medication may clump or crystallize making it unusable for administration. Examples of diluents include normal saline (NS), sterile water for inject (SWFI), Dextrose 5% in water (D 5W), or lidocaine 1% plain.